http://www.northeastcrawlers.com/necforum Post anything you have for sale. en Wed, 08 Sep 2010 05:42:57 GMT vBulletin 60 http://www.northeastcrawlers.com/necforum/images/misc/rss.jpg http://www.northeastcrawlers.com/necforum http://www.northeastcrawlers.com/necforum/showthread.php?t=8912&goto=newpost Wed, 08 Sep 2010 02:08:51 GMT I bought this in August, thinking that I would have some time to play with it this past month. I've been too busy to even think about it, and now it's time to start grad school so it's for sale.

DESCRIPTION:
It's a trailer to store and haul all your camping gear. Maybe a quad if you took the lid and back off. It's the same width as a Jeep. The tongue is just the right length that you can jacknife the trailer without hitting the tub of the Jeep. Box is 5' wide 6' long and 32" deep. Custom built by the previous owner. It's made of 2x2 and 2x4 box tubing, 2 inch angle iron, galvanized sheet metal, and OSB. 32" mud kings (including the spare). Bolt pattern is 5 x 5.5. 15" rims. I'm not sure what the trailer originally was, but the trailer is lifted spring over, and the previous owner added shocks to keep it from bouncing around.

CONDITION:
Roy might call it "ugly arse" because some paint is peeling off the lid, but other than that it's in good shape. The wood is dry and solid. It has 4-pin wiring, but the ground wire is broken, so the lights are currently out of commission. I'll see what I can do tomorrow about that.

For pics: http://www.ohio4x4.com/forum/showthr...amping-Trailer

Currently located in Zanesville OH 43701. I can bring it to Columbus 43201 this weekend, only if you can pick it up this weekend. $500 OBO. Call or text me at 740 two two one 28 31 if interested. ]]> For Sale SHAKEnBLAKE http://www.northeastcrawlers.com/necforum/showthread.php?t=8912 http://www.northeastcrawlers.com/necforum/showthread.php?t=8910&goto=newpost Sun, 05 Sep 2010 13:31:55 GMT If interested in any of this please email me at spyder873@comcast.net. I seem to be having issues with the pm thing. Thanks Seats 80 for all three, I dont have a picture of the rear but its the same color and cloth Image:... If interested in any of this please email me at spyder873@comcast.net. I seem to be having issues with the pm thing. Thanks

Seats
80 for all three, I dont have a picture of the rear but its the same color and cloth




Rear seat mounting brackets $30


Yj Radio support $10


Tj Heater Grill . Above the Radio. $10



Gray dash pad , no cracks but faded----- $10



Red Hood --- $25----sale pending
]]> For Sale spyder873 http://www.northeastcrawlers.com/necforum/showthread.php?t=8910 http://www.northeastcrawlers.com/necforum/showthread.php?t=8901&goto=newpost Sun, 29 Aug 2010 14:52:01 GMT complete engine and auto trans out of a 97 ram 3/4 ton 108000 miles , $600 or best offer great swap for a jeep 2002 and older because you can get a wiring harness thru backwoods offroad for $600 complete engine and auto trans out of a 97 ram 3/4 ton 108000 miles , $600 or best offer



great swap for a jeep 2002 and older because you can get a wiring harness thru backwoods offroad for $600 ]]> For Sale jeepdaddytj http://www.northeastcrawlers.com/necforum/showthread.php?t=8901 http://www.northeastcrawlers.com/necforum/showthread.php?t=8899&goto=newpost Thu, 26 Aug 2010 18:23:37 GMT 1976-06 Wrangler and CJ
Made of 3/16" x 2" x 4" tubing and come with an integrated CNC laser cut winch plate, roller fairlead mount and holes for lights at outer edge of winch plate
Comes with an angled forward hoop for the rock crawler
Uses factory bumper hardware for installtion
Rock Hard 4x4 Jeep Front Bumpers are designed for heavy duty use in the rocks. made of 3/16 x 2 x 4 tubing and come with an integrated CNC laser cut winch plate, roller fairlead mount and holes for lights at outer edge of winch plate. This bumper also comes with an angled forward hoop for the rock crawler look, 2-5/8 x 2 1/2 CNC D-Ring shackle mounts welded front and back for ultimate strength and a mounting plate for a steering box protector. Black Powder Coated. $325 new

Located in Brackenridge,pa. or email spyder873@comcast.net



]]> For Sale spyder873 http://www.northeastcrawlers.com/necforum/showthread.php?t=8899 http://www.northeastcrawlers.com/necforum/showthread.php?t=8898&goto=newpost Thu, 26 Aug 2010 18:18:26 GMT I've got some 9" HID off road lights I want to get rid of. They're new in the box and never used. I have 6 total.

$ 129 each new at the store
$ 79 each new from me.

Shipping will be $10 per light.

]]> For Sale FUBAR http://www.northeastcrawlers.com/necforum/showthread.php?t=8898 http://www.northeastcrawlers.com/necforum/showthread.php?t=8894&goto=newpost Tue, 24 Aug 2010 20:00:55 GMT 1997 Jeep Cherokee, 4 door, automatic, 4.0L, 153k miles, white, power windows & locks.

Recent Upgrades:
6" FullTraction Long Arm w/ Belly skid
Slip Yoke Eliminator & TW Driveshaft
4.56 Gears
Aussie Locker in 8.25 Rear axle
Ox Locker in HP D30 Front axle
New (less than 100 miles) 35x12.50 GoodYear MT/R w/ Kevlar on black steel wheels
Rusty's Flexible Flares
JRA Rocksliders
Smittybilt Gas Tank Skid

Recent Repairs:
Transmission Flush
Radiator Flush
New Fuel Pump
New Injectors
New Exhaust
A/C Repaired with new condensor & evap. core

7900 OBO.







]]> For Sale Prope http://www.northeastcrawlers.com/necforum/showthread.php?t=8894 http://www.northeastcrawlers.com/necforum/showthread.php?t=8893&goto=newpost Tue, 24 Aug 2010 19:08:47 GMT I'm selling a 4.3 Vortec out of a 94 Blazer. I'm asking $400 for the engine. I also have a Painless Performance wiring harness for the 4.3. Its Painless part number PWP60210. More info on the harness can be found here.. http://www.painlessperformance.com/w...&SearchAll=4x4 .
I bought the harness less than a month ago and its been sitting in my house ever since. Still Brand New in the box. Looking to get $400 for the harness. ]]> For Sale JamesB http://www.northeastcrawlers.com/necforum/showthread.php?t=8893 http://www.northeastcrawlers.com/necforum/showthread.php?t=8892&goto=newpost Tue, 24 Aug 2010 12:06:36 GMT Selling my 1988 Bronco II. Odometer reads 58000. It is actually 158000 thousand but the odometer doesn't read that high. engine, trans and both axles were swapped at around 155000. Engine and trans had approx. 89000 miles on them at install. This truck has been built since mid 2007. From then until December it was trailered to and from the trails. Since December it has seen approx 1500 rd miles and a few offroading trips. It is tagged and insured in Ohio, and aside from some funny vibrations from he tires it will run 70+mph down the freeway with no issues.


Drive train:
1995 4.0 engine, 4r55e automatic trans out of 1996 Ranger, 1354 manual transfercase from a 94 explorer. Engine had new water pump, idler pulley new plugs, wires,and fuel filter done at install . Transmission was also flushed with a new filter.

Axles:
Front is a d35 from a 94 explorer it has a 4.56 Yukon gear set, Aussie locker ( installed in may)w/ c-clip eliminator. Rotors and caliper were replaced when truck was built. Was also converted to manual WARN lock out hubs..(have a couple extra lockouts and axle sahfts included) Has extended James duff stainless steel brake lines. I did new u joints, spindle bearings and axle seals when I put the locke rin in may. Also repacked the front wheel bearings.

Rear axle is a 31 spline 8.8 with disc brakes from 96 explorer The rear has a set of riverside 4.56’s and a Detroit lunch box locker. All bearings and seal where replaced when truck was built

Lift:
3” Performance Accessories body lift.
Suspension lift is a 3” James Duff. w/ variable rate springs in front w/ 30/70 oil filled shocks. Rear is the 3” Duff add-a-leaf (NO BLOCKS). Rear shocks are 40/60 oil filled.
This thing rides nice and smooth on the rd and handles the rough trails with ease. Flexes out nicely to boot.


Other Mods: Roof rail sliders. Have had the entire weight of the truck against a tree and no rear broken window’s.
Front bumper is a huge 1/4" thick piece of steel that was put on there TWO owners ago, however it has had the corners cut to gain clearance and is flush with he bottom of the frame rails.It now has the 8000# winch mounted behind it with roller fair lead on the front. The winch solenoids were moved under the hood next to the fire wall to keep them mud free. There is a winch control plug under the left head light and there is one on the dash inside the spot where the cig lighter used to be. (no more control wire running across the hood and dragging in the mud.) It has two d-rings on the front of it and two tow hooks on the frame rails.
Has a dual battery set-up. Both are mounted under hood with a battery isolator, charges both at the same time. Winch runs off second battery. Doors are pinned for easy removal.

Tires: 4 Almost brand new 35-12.50-15 km2's. Spare tires is a 35" off brand all terrain, has 5 matching bead locks built by Lost Valley Jeep. Approx 800 miles on tires and wheels.

THIS IS A DEDICATED TRAIL RIG ( that is driven to and from the traisl) THEREFORE IT HAS DENTS ( alot of them, comes with two rust/dent free fenders) AND SCRATCHES. IT IS NOT A SHOW TRUCK! It WILL HANDLE DD DUTIES BUT IT ISNT THE MOST PRACTICAL THING FOR SUCH!


$2800 located in Roseville Ohio, however when I sold my Jeep Liberty I had to transfer some of the collateral over to this( I was upside down on the Liberty loan) so we will need to go to my bank in Lancaster to get the title. I work in Lancaster and can drive this to work any day of the week so it can be viewed as-well.


SOME trades considered. I am looking for a half ton or bigger extended cab pickup truck 4wd would be nice but not needed. Would also consider trade for a 4x4 utility atv. Have no interest in anything FWD, or another trail rig.



I can provide more and better photos if requested. ]]> For Sale offroadohio http://www.northeastcrawlers.com/necforum/showthread.php?t=8892 http://www.northeastcrawlers.com/necforum/showthread.php?t=8886&goto=newpost Fri, 20 Aug 2010 14:06:47 GMT http://www.lundinternational.com/products/tonneaus/genesis-roll-up-tonneau/ Fits 1999-06 Chevrolet and GM Silverado and Sierra with standard bed sides or 78.0 in./6 ft. 6 in. Bed. Had a small tear in it, about the size of a dime that I patched. Other than that, in excellent condition. ... http://www.lundinternational.com/pro...ll-up-tonneau/

Fits 1999-06 Chevrolet and GM Silverado and Sierra with standard bed sides or 78.0 in./6 ft. 6 in. Bed.

Had a small tear in it, about the size of a dime that I patched. Other than that, in excellent condition.

Asking $200 or best offer. ]]> For Sale TJMagoo http://www.northeastcrawlers.com/necforum/showthread.php?t=8886 http://www.northeastcrawlers.com/necforum/showthread.php?t=8875&goto=newpost Thu, 12 Aug 2010 18:18:57 GMT Posting this for a buddy. Black 99 TJ fuel injected 302 V8 zf 5 speed manual tranny np 205 transfer case D30 with ox locker, 4.56 gears and alloy shafts rear D44 with ox locker and 4.56 gears 4 inch rock krawler long arm suspension currie tie rod/drag link Posting this for a buddy.

Black 99 TJ
fuel injected 302 V8
zf 5 speed manual tranny
np 205 transfer case
D30 with ox locker, 4.56 gears and alloy shafts
rear D44 with ox locker and 4.56 gears
4 inch rock krawler long arm suspension
currie tie rod/drag link
A to Z Rockers
Hombrew front bumper
Warn rear bumper/tire carrier

$5,000 obo, trades considered

Its not perfect, body has some dings, but is a pretty good jeep.

His name is Jason & I'll pm you his # if you are interested ]]> For Sale Prope http://www.northeastcrawlers.com/necforum/showthread.php?t=8875 http://www.northeastcrawlers.com/necforum/showthread.php?t=8870&goto=newpost Mon, 09 Aug 2010 23:20:08 GMT 1993 grille black -$100 yj windshield frame in great condition , glass has a crack -$150 yj axles d30/d35 3.07 gears ,clean and in nice shape-$275 a pair yj leaf springs , all four $150 steering column -$100 all prices are obo or package deal $600 for everything 1993 grille black -$100
yj windshield frame in great condition , glass has a crack -$150
yj axles d30/d35 3.07 gears ,clean and in nice shape-$275 a pair
yj leaf springs , all four $150
steering column -$100

all prices are obo or package deal $600 for everything ]]> For Sale jeepdaddytj http://www.northeastcrawlers.com/necforum/showthread.php?t=8870 http://www.northeastcrawlers.com/necforum/showthread.php?t=8869&goto=newpost Mon, 09 Aug 2010 18:45:48 GMT selling my bike, it's a 03 honda rc51 1000 twin, Full Yosh stainless pipes, newer tires (about 1k mi on them) exhaust flapper valve removed, for more power, power commander, frame sliders, and very clean, I'll regret this down the road but I am going to get something more comfortable for the wife and I ..

13k miles
$5250 OBO or trade...


will post a few pics when I get back home tonight


thanks -Jason

PS. Bike is faster then crack! ]]> For Sale Trail_TJ http://www.northeastcrawlers.com/necforum/showthread.php?t=8869